What is the take-up amount for a stub-up bend using 1-inch IMC? A. 8 inches B. 16 and 5/8 inches C. 5 and 5/8 inches D. 11 inches

Question and answer

Question

Asked 5/12/2016 2:29:22 PM

Updated 6/15/2019 11:48:22 PM

1 Answer/Comment

Get an answer

Search for an answer or ask Weegy.

Original conversation

User: What is the take-up amount for a stub-up bend using 1-inch IMC? A. 8 inches B. 16 and 5/8 inches C. 5 and 5/8 inches D. 11 inches

Weegy: 5 5/8" is the take-up amount for a stub-up bend using 1-inch IMC.
bibiolay17|Points 101|

User: When installing conduit for a mast service, what type of conduit should you use? A. EMT B. IMC C. Rigid-metal D. Rigid-nonmetal

Question

Asked 5/12/2016 2:29:22 PM

Updated 6/15/2019 11:48:22 PM

1 Answer/Comment

New answers

Rating

maydj

When installing conduit for a mast service, you should use rigid-nonmetal conduit.

Added 6/15/2019 11:48:22 PM

This answer has been confirmed as correct and helpful.

Rated bad by Allizdog2

Comments

There are no comments.

Add an answer or comment

Questions asked by the same visitor

mpacity, or the maximum flow of electricity for a time period, A. increases as wire diameter increases. B. decreases as wire number decreases. C. increases as wire number increases. D. isn't dependent on wire diameter or number.

(More)

Question

Not Answered

Updated 7/28/2021 6:32:57 AM

1 Answer/Comment

Cezss

Ampacity, or the maximum flow of electricity for a time period, increases as wire diameter increases.

Added 7/28/2021 6:32:57 AM

This answer has been confirmed as correct and helpful.

When soldering a lug onto a copper wire, you would use A. both plain solder and an acid. B. rosin-core solder only. C. plain solder without flux. D. acid-core solder only.

(More)

Question

Not Answered

Updated 10/20/2018 6:47:28 AM

1 Answer/Comment

andronep

When soldering a lug onto a copper wire, you would use rosin-core solder only.

Added 10/20/2018 6:47:28 AM

This answer has been confirmed as correct and helpful.

Confirmed by matahari [10/20/2018 7:08:04 AM]

The position from which you write about your subject is called your A. standpoint. B. prerogative. C. point of view. D. advantage.

(More)

Question

Not Answered

Updated 11/21/2016 3:47:04 PM

1 Answer/Comment

destle6

The position from which you write about your subject is called your point of view.

Added 11/21/2016 3:47:04 PM

This answer has been confirmed as correct and helpful.

Confirmed by yumdrea [11/21/2016 6:32:51 PM]

f a comment is culturally insensitive, it's one that may be considered _______ to certain groups or cultures. A. offensive B. savvy C. redundant D. awkward

Weegy: If a comment is culturally insensitive, it's one that may be considered offensive to certain groups or cultures. User: The information included in the Works Cited page must correspond with A. the information listed in the introduction of your essay. B. the conclusions you have drawn from your research. C. the citations included within the body of your essay. D. the number of individual authors used in your resea (More)

Question

Not Answered

Updated 7/10/2019 5:12:28 PM

1 Answer/Comment

maydj

The information included in the Works Cited page must correspond with the citations included within the body of your essay.

Added 7/10/2019 5:12:28 PM

This answer has been confirmed as correct and helpful.

An idea that's intended to make the reader take notice and want to read on is called a A. summary. B. point of view. C. presentation. D. hook. User: Read the following paragraph. Then answer the question that follows it. Stand before a mirror. Put the bow tie under your collar. Pull the right end so that it's an inch or two longer than the left end. Now take the right end with your right hand and loop it over the left end. Pull it up inside and then cross it, so that it hangs again on ...

Weegy: The author instructs the reader to pull the ends of the bow tie tight until both ends are just about the same length. -is an example of a paraphrase. User: The indentation style used on a Works Cited page is called A. block indent. B. hanging indent. C. standard indent. D. reverse indent. Weegy: To indent is to start (a line of text) or position (a block of text, table, [ etc.) further from the margin than the main part of the text. ] User: Failure to incorporate _______ can easily lead to _______. A. denotation, connotation B. parallelism, structure C. citations, plagiarism D. discipline, bias User: The best way to ensure parallel construction in your essay is to use similar A. sentence structure throughout the essay. B. details in each paragraph. C. topic headings in the outline. D. paragraph lengths. (More)

Question

Not Answered

Updated 1/18/2021 1:29:23 AM

1 Answer/Comment

maydj

The best way to ensure parallel construction in your essay is to use similar sentence structure throughout the essay.

Added 1/18/2021 1:29:23 AM

This answer has been confirmed as correct and helpful.

37,542,445

questions answered