Question and answer
Maurice is an electrician installing a free-standing electric range. He'll use the 50-ampere receptacle that comes equipped with a 50-ampere rated pigtail. What must he remember with regards to the pigtail? A. Never use it as a disconnecting means for the circuit. B. It's safer to connect the range directly into the wall-mounted junction box. C. He'll need a maximum of six inches of wire when hooking it up. D. Never use it to extend the length of the wire.
Maurice is an electrician installing a free-standing electric range. He'll use the 50-ampere receptacle that comes equipped with a 50-ampere rated pigtail. He must remember with regards to the pigtail is: It's safer to connect the range directly into the wall-mounted junction box.
f
Question|Asked by amelvin41
Asked 2/8/2019 5:24:20 PM
Updated 9/14/2022 4:45:45 PM
1 Answer/Comment
Get an answer
New answers
Rating
3
Maurice is an electrician installing a free-standing electric range. He'll use the 50-ampere receptacle that comes equipped with a 50-ampere rated pigtail. He must remember with regards to the pigtail is: It's safer to connect the range directly into the wall-mounted junction box.

Added 9/14/2022 4:45:45 PM
This answer has been confirmed as correct and helpful.
Comments

There are no comments.

Add an answer or comment
Log in or sign up first.
Questions asked by amelvin41
Which type of circuit is becoming more common in residential electrical design and construction? A. Hazardous-area circuit B. Three-phase circuit C. 480-volt circuit D. Communication circuit
Question|Asked by amelvin41
Not Answered
Updated 4/20/2021 11:04:24 PM
1 Answer/Comment
Communication circuit is becoming more common in residential electrical design and construction.
Added 4/20/2021 11:04:24 PM
This answer has been confirmed as correct and helpful.
To protect all four receptacles on a branch circuit that surrounds a swimming pool, you would install which of the following configurations? A. GFCI feed-through receptacle at the end of the load's circuit B. GFCI-terminated receptacle at the beginning of the load's circuit C. GFCI feed-through receptacle at the beginning of the load's circuit and the other receptacles connected to the load side of that receptacle D. GFCI-terminated receptacle at each end of the load's circuit
Question|Asked by amelvin41
Not Answered
Updated 9/14/2022 4:58:24 PM
1 Answer/Comment
To protect all four receptacles on a branch circuit that surrounds a swimming pool, you would install the following configurations: GFCI feed-through receptacle at the beginning of the load's circuit and the other receptacles connected to the load side of that receptacle.
Added 9/14/2022 4:58:24 PM
This answer has been confirmed as correct and helpful.
When using two-wire cable to feed a 240-V appliance that does not require a neutral wire, you should A. mark both ends of the white wire green. B. use the cable as is. C. use only the black wire. D. mark both ends and any exposed area of the white wire black.
Question|Asked by amelvin41
Not Answered
Updated 9/14/2022 4:57:00 PM
1 Answer/Comment
When using two-wire cable to feed a 240-V appliance that does not require a neutral wire, you should mark both ends and any exposed area of the white wire black.
Added 9/14/2022 4:57:00 PM
This answer has been confirmed as correct and helpful.
When using two-wire cable to feed a 240-V appliance that does not require a neutral wire, you should A. mark both ends of the white wire green. B. use the cable as is. C. use only the black wire. D. mark both ends and any exposed area of the white wire black.
Question|Asked by amelvin41
Not Answered
Updated 9/14/2022 4:56:27 PM
1 Answer/Comment
When using two-wire cable to feed a 240-V appliance that does not require a neutral wire, you should mark both ends and any exposed area of the white wire black.
Added 9/14/2022 4:56:27 PM
This answer has been confirmed as correct and helpful.
When calculating the general light and receptacle load for a residence, you multiply the square footage of the house by _______ VA. A. 40 B. 3 C. 100 D. 10,000
Question|Asked by amelvin41
Not Answered
Updated 2/4/2019 10:04:47 PM
1 Answer/Comment
When calculating the general light and receptacle load for a residence, you multiply the square footage of the house by 3 VA.
Added 2/4/2019 10:04:47 PM
This answer has been confirmed as correct and helpful.
38,921,191
questions answered
Popular Conversations
Who was a political organizer that led the independence movement in ...
Weegy: Samuel Adams was a political organizer who the led the independence movement in Boston. User: What was the ...
2/24/2024 1:45:58 AM| 15 Answers
During the Civil War Southern leaders hoped that
Weegy: During the civil war southern leaders hoped that European countries would give their support. User: What ...
2/24/2024 2:15:42 AM| 6 Answers
whats the role of the suns gravity in the solar system
Weegy: 1 + 1 = 2 User: what does einstein's theory of relativity explain Weegy: Einstein's theory of relativity ...
2/24/2024 9:17:58 PM| 6 Answers
How did Ralph Waldo Emerson impact American society?
Weegy: Ralph Waldo Emerson impacted American society by: He led the transcendentalist movement. User: Who invented ...
2/24/2024 1:54:52 AM| 5 Answers
whats was a characteristic of yellow river
2/27/2024 12:15:36 PM| 4 Answers
Spanish explorers who used military force against indigenous peoples ...
Weegy: Spanish explorers who used military force against indigenous peoples while looking for wealth were called: ...
2/23/2024 7:19:10 PM| 4 Answers
S
L
Points 51 [Total 631] Ratings 0 Comments 51 Invitations 0 Online
S
Points 28 [Total 81] Ratings 0 Comments 28 Invitations 0 Offline
S
L
Points 4 [Total 3020] Ratings 0 Comments 4 Invitations 0 Offline
* Excludes moderators and previous
winners (Include)
Home | Contact | Blog | About | Terms | Privacy | © Purple Inc.