Look at the engine in Figure A-2. What type of cylinder arrangement does it have?

Question and answer

Question

Asked 9/19/2012 4:26:53 PM

0 Answers/Comments

This answer has been confirmed as correct and helpful.

Get an answer

Search for an answer or ask Weegy.

Original conversation

User: Look at the engine in Figure A-2. What type of cylinder arrangement does it have?

Weegy: ... at the engine in figure A-2 What type of cylinder arrangment does it have and said it was the same as Look at the engine in Figure A-2 What type [ of cylinder arrangement ... ]

User: What type of cylinder arrangement does it have

Weegy: What type of cylinder arrangement does it have in figure a-2? We cant see figure A-2. [ So i would recommend either scanning the photo, and then uploading it somewhere ... ]

User: _______ are fasteners that connect parts and are intended to resist pulling forces

Weegy: ... is not always required, but fasteners that ... corner, tightly fitting dovetails resist twisting forces... ... [ and pegging rather than nails to connect a building's structural parts ... ]

User: _______ are fasteners that connect parts and are intended to resist pulling forces. A. Compression springs B. Lock washers C. Wedges D. Extension springs

Weegy: A. Compression springs are fasteners that connect parts and are intended to resist pulling forces.
Expert answered|OxTornado007|Points 5448|

Question

Asked 9/19/2012 4:26:53 PM

0 Answers/Comments

This answer has been confirmed as correct and helpful.

New answers

Rating

There are no new answers.

Comments

There are no comments.

Add an answer or comment

Questions asked by the same visitor

The percolating temperature of an automatic percolator is kept at the desired level by the A. ON/OFF switch. B. thermostat. C. automatic valve. D. low-heat element

Weegy: The percolating temperature of an automatic percolator is kept at the desired level by the B. thermostat. (More)

Question

Expert Answered

Asked 9/13/2012 4:16:01 PM

0 Answers/Comments

Weegy: A. BAKING SODA SOLUTION. (More)

Question

Expert Answered

Asked 9/13/2012 6:25:20 PM

0 Answers/Comments

When plug prongs are connected to the metal case of an appliance, a part that should always be placed next to the case is a

Weegy: When plug prongs are connected to the metal case of an appliance a part that should always be placed next to the case is what? [ ] User: When plug prongs are connected to the metal case of an appliance, a part that should always be placed next to the case is a A. flat metal washer. B. hexagonal aluminum shoulder. C. steel nut. D. mica washer. Weegy: plug prongs are connected to the metal case of an appliance, a part that should always be placed next to the case is a A. flat metal washer. (More)

Question

Expert Answered

Asked 9/13/2012 7:56:24 PM

0 Answers/Comments

An employee who interacts with customers regarding the nature of their car problems, rather than actually working on the vehicles, is called a

Weegy: Asked An employee who interacts with customers regarding the nature of their car problems rather than actually working on the vehicles is called and [ said it was the same ... ] User: An employee who interacts with customers regarding the nature of their car problems, rather than actually working on the vehicles, is called a A. service writer. B. stock technician. C. diagnostic technician. D. front end specialist Weegy: An employee who interacts with customers regarding the nature of their car problems, rather than actually working on the vehicles, is called a: C. diagnostic technician. (More)

Question

Expert Answered

Asked 9/19/2012 12:18:29 PM

0 Answers/Comments

In an automotive engine, the pattern in which the cylinders are ignited is called the A. VIN number. B. redline. C. compression ratio. D. firing order.

Weegy: D. firing order. the pattern in which the cylinders are ignited is called the firing order. (More)

Question

Expert Answered

Asked 9/19/2012 3:46:50 PM

0 Answers/Comments